Every resin print is finished in three steps: wash off the liquid resin, let it dry completely, then cure it under UV light until it is fully hard. A wash and cure station does the first and last in one machine, sized to your printer's build plate. These are the stations sold by the shops we track in the most markets:

Combined UV curing and IPA/water washing station for resin prints, current flagship model
ELEGOO

Combined ultrasonic wash and UV cure station for resin prints, the entry model in Anycubic's current line
Anycubic

Larger-capacity wash and UV cure station, fits taller/wider prints than the base Wash & Cure 3
Anycubic

Resin wash and cure machine
Creality

Combined wash and UV cure station for resin prints
Phrozen

Prusa wash-and-cure station for resin prints
Prusa
Every station, lamp and chamber we track is on the UV curing shelf.
How to wash and cure resin prints
- Wash. Standard and ABS-like resins wash in isopropyl alcohol (IPA); water-washable resin in water. A wash station spins or agitates the liquid around the print.
- Dry. Let the print dry completely. Formlabs' instruction for its own station is to "always wash and fully dry parts before post-curing", because solvent left on the part leaves deposits inside the curing chamber. Phrozen gives the same advice for its water-washable tough resin.
- Cure. Put the print under UV light, turning it if your station does not, until it is hard and no longer tacky.
How long to cure resin prints
The right time depends on the resin and the light, so start from the time on your resin's bottle or its maker's page. Our best resin for miniatures guide compares the resins. Stations set the time with a timer, so once you know the figure for your resin, each batch gets the same.
All-in-one wash and cure stations
One machine with a wash tank and a turntable under UV lamps. You swap the tank for the turntable between the two steps. The main thing to check is size: the station has to fit your printer's build plate, or the biggest print you make.
| Station | Wash size (max) | Cure size (max) | Stated details |
|---|---|---|---|
| ELEGOO Mercury Plus V3.0 | 230 x 135 x 260 mm without the plate; 214 x 135 x 180 mm with it | 250 mm across, 290 mm high | UV cover blocks 99.9% of UV; curing stops when the cover is lifted |
| Anycubic Wash & Cure 3.0 | 165 x 100 x 180 mm without the plate | 160 x 180 mm | 3 L tank; Anycubic sizes it for printers of 7.3 inches or less; 405 nm light |
Figures from 3DJake's listings for each station. The larger Anycubic Wash & Cure 3 Plus and 3 Max take taller and wider prints; the Max is sized for Anycubic's P1 Max and M7 Max printers.

Combined UV curing and IPA/water washing station for resin prints, current flagship model
ELEGOO

Combined UV curing and IPA/water washing station for resin prints
ELEGOO

Combined ultrasonic wash and UV cure station for resin prints, the entry model in Anycubic's current line
Anycubic

Larger-capacity wash and UV cure station, fits taller/wider prints than the base Wash & Cure 3
Anycubic

Largest wash and UV cure station in the current range, sized for the P1 Max and M7 Max printers
Anycubic

Resin wash and cure machine
Creality
Separate washers and curing chambers
Two machines cost more and take more bench space, but you can wash one batch while the last one cures, and each machine can be bigger than an all-in-one. ELEGOO's Mercury XS bundle is a wash station and a cure station sold together.
Ultrasonic cleaners
An ultrasonic cleaner washes with vibration rather than a spinning tank. The Phrozen and VEVOR cleaners here are listed for washing resin prints in a sealed jar of IPA that stands in the cleaner's water bath, so the alcohol stays in the jar and out of the tank.

10 L ultrasonic cleaning tank for resin prints (IPA in a sealed container inside the water bath) and airbrush parts · 10 L · us_001387
Phrozen

Heated ultrasonic cleaning tank (resin-print wash with IPA in a sealed jar; airbrush needles, nozzles and cups) · 3 L · 240 x 135 x 100 mm · 265 x 165 x 240 mm · 120 W · 300 W · 40 kHz · KZ-F3 · Digital, 0-30 min, 0-80 °C, gentle and degas modes · HGKCSBQXJ3LAPZ00BV1 · 197988655770
VEVOR

Heated ultrasonic cleaning tank (resin-print wash with IPA in a sealed jar; airbrush needles, nozzles and cups) · 6 L · 300 x 150 x 150 mm · 325 x 175 x 295 mm · 180 W · 500 W · 40 kHz · Digital, 0-30 min, 0-80 °C, gentle and degas modes · HGKCSBQXJ6LAHTSPMV1 · 197988843863
VEVOR
UV lamps and curing chambers on a budget
If you already have a wash tub, a UV chamber or lamp does the curing. Green Stuff World's UV Curing Chamber is a mirrored 405 nm chamber of 195 x 160 x 150 mm inside, and its UV torch spot-cures a join or a small part. Gluing resin parts with a dab of resin is covered in our glue guide for 3D prints.
12-LED 385-400nm UV-A flashlight for spot-curing resin · 3 x AAA (not included), about 4.5 hours
Green Stuff World

UV curing chamber for resin prints · 7SUMA004K01
SUMAOPAI

Handheld UV pen for spot-curing resin prints and joins
Phrozen
A resin printing workspace: bench, ventilation and the wash and cure station
Resin printing is messy and smelly before it is difficult, so set the workspace up before you pour the first bottle.
- A room with a window, away from where you sleep and eat. Liquid resin and the alcohol you wash it in both give off a smell, and the resin's own safety data sheet tells you what to wear and how to ventilate.
- A bench you can wipe down, with the printer, the wash station and the curing station in one line: print, wash, dry, cure. Lay down a disposable mat or tray under all three, since spills happen at the moment you move a plate.
- Nitrile gloves and eye protection for handling liquid resin and anything still wet. Nitrile gloves are not fully resin-proof, so change them if resin gets on them, wash skin with soap and water, and do not look at the UV lamp or leave skin under it.
- A steady temperature. Resin flows and cures best at a stable room temperature, which is the main reason people put a printer in an enclosure. Our 3D printer enclosure guide covers tents, rigid boxes and what they do for fumes.
- A place to leave the wash station and the used IPA, with the lid on, away from heat and any ignition source: IPA is flammable.
An activated-carbon air purifier reduces the smell. ELEGOO, Anycubic and Phrozen each sell one made for their own printers, and a ventilated tent holds the whole printer. An enclosure or purifier is an addition to ventilating the room, not a replacement for it.

Ducted 6-layer air purifier for resin and FDM printers
Phrozen

Air purifier for 3D printing, resin-printer version · 250 m3/h · 1000 hours
Creality

Ventilated fabric tent enclosure for a resin (LCD) printer, venting fumes and holding temperature; titled for Photon Mono / Mars 3 · S0003 · 600D Oxford cloth, inner composite aluminium film · 550 x 650 x 750 mm (L x W x H) · 3DDYJZRTWQYTRD8OP001V9 · 197988168577
VEVOR
Washing bucket for Mercury Plus V3.0 wash-and-cure station spares
ELEGOO

Spare part for 3D printer
ELEGOO

Spare wash container for the Phrozen Wash & Cure Kit · Phrozen Wash & Cure Kit
Phrozen
Getting rid of the wash liquid
Used IPA and wash water carry uncured resin. Phrozen's rule for water-washable resin is: "Don't pour uncured water directly down the drain." Leave it in sunlight for a few days so the resin cures, filter out the solids and put them in the rubbish.
Questions
How long should I cure resin prints?
Start from the time your resin's maker gives, since it depends on the resin and the light. Wash and dry the print fully first.
Do I need a wash and cure station?
No. A tub of isopropyl alcohol (or water for water-washable resin) and a UV lamp or chamber do the same jobs. A station makes it quicker and tidier.
Should prints be dry before curing?
Yes. Formlabs says to always wash and fully dry parts before post-curing, and Phrozen gives the same advice for its water-washable tough resin.
Where should I set up a resin printer?
In a room with a window, away from where you sleep and eat, on a wipe-clean bench in a line from print to wash to cure. An enclosure or air purifier helps with the smell, and the room still needs ventilating.
Can I pour resin wash water down the drain?
No. Phrozen says not to. Let the water stand in sunlight until the resin in it cures, then filter out the solids.
We compare what the makers and the shops we track publish, and their prices; we have not used these stations ourselves.



