Hobby SupermarketHobbySupermarket

Gunpla Tools: What You Actually Need

Nippers first, then a knife and something to sand with

A High Grade Gunpla kit needs one tool: a pair of nippers to cut the parts from the runner. Everything else on this page makes the finished kit look cleaner, and you can add it kit by kit. (An Entry Grade needs nothing at all: Bandai design its parts to come off the runner by hand, as our grades guide explains.)

Start with nippers. These are the ones the shops we compare sell in your market:

Every cutter we price is on our cutting and prep shelf.

The shops we compare in this market do not sell nippers yet, so the cutter cards on this page are empty here. A hobby knife is the one tool on this page every market can buy.

The short list

ToolDo you need it?What it does
NippersYes, for anything above Entry GradeCuts parts off the runner
Hobby knifeStrongly recommendedShaves the leftover nub flush
Sanding sticks or filesRecommendedSmooths the white mark the cut leaves
Panel linerOptional, but the biggest visual changeDarkens the engraved lines
Top coatOptionalSeals stickers and lines, takes the shine off
TweezersOptionalPlaces small stickers and decals
Cutting matOptionalProtects the table from the knife

Nippers

Gunpla nippers are small side cutters with thin jaws, made for soft plastic runners. Bandai sell their own as the Entry Nipper and the Build Up Nipper, and most hobby brands make a pair. What separates a good pair is how flat a face it leaves on the part: a single-blade (flush) nipper cuts one side flat against the part, where a double-blade pair squeezes the plastic and leaves a pale, stressed stub.

Our sprue cutter guide goes through single-blade against double-blade, what GodHand nippers do, and how to keep a fine blade from chipping.

Cut twice. Cut the part off a few millimetres away from it first, then trim the leftover nub close to the part with a second cut. Cutting tight against the part on the first go is what leaves stress marks.

Bandai Spirits Build Up Nipper

Bandai

  • postage per seller

A hobby knife

A sharp knife takes off the last sliver of nub that the nippers leave, and scrapes away any mould line. Shave towards the part's surface in light strokes rather than digging in, and change the blade as soon as it drags. Our hobby knife guide compares the knives.

Army Painter Hobby Knife

Hobby knife with a moulded grip

Army Painter

  • postage per seller
  • postage per seller
  • postage per seller
Citadel Tools: Knife

Citadel hobby knife

Citadel

  • postage per seller
  • postage per seller
  • postage per seller
Jakar Hobby Knife with 6 Assorted Blades

Screw-collet hobby knife supplied with 6 different blade shapes (7344-B, 7360-B, 7361-B, 7362-B, 7363-B, 7364-B)

Jakar

Vallejo Tools Soft Grip Craft Knife No. 1 with No. 11 Blade

Soft-grip No. 1 knife supplied with a No. 11 blade

Vallejo

  • postage per seller
  • postage per seller
  • postage per seller
Gale Force Nine Precision Micro Knife

Fine micro knife for detail cutting

Gale Force Nine

  • postage per seller

Sanding: the white marks

Where a gate is cut, coloured Gunpla plastic often goes white. Sanding the spot smooth, working up from a coarser grit to a finer one, removes most of the mark, and a matt top coat hides what is left. Sanding sticks and foam pads are easier to keep flat on a part than loose paper.

Gunprimer also sell a dedicated gate remover, the Raser, as a starter kit with its abrasives. It is a tool for builders who already do a lot of kits.

Panel lining and top coat

These two finishing steps make more difference to a straight build than any other tool. Panel lining runs a dark wash into the engraved lines; a top coat seals it and takes the plastic shine off. Both have their own guide: how to panel line Gunpla, and top coat it, with every panel liner and varnish we price. To paint the kit itself, with Gundam Markers, acrylic or lacquer, see the best paint for Gunpla.

Army Painter Anti-Shine Matt Varnish

Matt anti-shine topcoat, 400ml aerosol

Army Painter

  • postage per seller
  • postage per seller

Tweezers and a cutting mat

Tweezers help with small stickers and water-slide decals, and a self-healing mat stops the knife marking the table. Neither is essential for a first kit.

What you do not need yet

  • Glue. Gunpla snaps together. Glue is only for modifying parts.
  • Paint. The plastic is moulded in colour, and on most kits the stickers do the rest.
  • The most expensive nippers. A single-blade pair is what a first kit needs; the dearest pairs can wait.

Tips

  • Buy nippers before anything else.
  • Cut twice: once away from the part, once close to it.
  • Sand the white marks, then top coat. The two together hide gate marks best.
  • Keep fine nippers for plastic. Metal and thick runners chip a thin blade.

Shop Gunpla tools

Nippers, files and finishing tools, compared across every shop we track.

We earn a small commission from qualifying purchases at no extra cost to you.

Price the hobby

Everything named on this site carries its price across the shops we track.

Hobby Supermarket

Prices on miniatures, paints, brushes, 3D printing and trading cards, compared across the shops we track in the UK, US, Europe, Canada and Australia.

Deals by email

Send me deals for
Tell us what you play (optional)
What are you into? (optional)
Which games?
Which card games?

As an Amazon Associate we earn from qualifying purchases. We also earn commission as a Wayland Games affiliate and through the eBay Partner Network, Awin and other retailer programmes. See how we make money.

Warhammer, Warhammer 40,000, Age of Sigmar, Citadel and Games Workshop are trademarks of Games Workshop Ltd. Magic: The Gathering is a trademark of Wizards of the Coast, Pokémon of Nintendo, Creatures and GAME FREAK, and Yu-Gi-Oh! of Konami. Other product and brand names belong to their owners. Hobby Supermarket is an independent, unofficial site, not affiliated with, endorsed or sponsored by any of them.

Featured on tools.cafe