Varnish is the last coat on a miniature and the one that decides whether the paint survives handling. A gaming army gets picked up by the base, the sides and sometimes the head, game after game, and an unvarnished model wears through on its edges first. A coat of varnish takes the wear instead.
The varnishes most miniature painters use, spray and brush-on, with prices from the shops we track in your market:

Matt anti-shine topcoat, 400ml aerosol
Army Painter


Matt protective topcoat, 18ml dropper
Army Painter

Matt protective topcoat, 60ml bottle · 26.702
Vallejo
Citadel (Warhammer Paints)
Citadel (Warhammer Paints)
Every varnish we list is on the varnishes and sealers shelf.
Matt, satin or gloss?
Gloss is the toughest finish and the one that protects best, but it makes a model look wet and plastic, and it hides detail under reflections. It is the right finish for gems, eyes, fresh blood, slime and polished armour, and a useful first coat under matt (see below).
Matt kills the shine. Most painters want it on cloth, skin, fur and bases, because acrylic paint dries with a slight, uneven sheen and a matt coat evens it out. Very flat ("ultra matt") varnishes can dull bright colours and metallics a little.
Satin sits between the two and is a good all-round choice for armour, leather and vehicles. Some painters use it everywhere and add gloss only on the details. Paints carry finishes of their own too: paint finishes covers matte, metallic and gloss paints.
A common professional routine: one coat of gloss for protection, one coat of matt on top for the look, then a dot of gloss back on eyes, gems and anything wet.
Spray or brush-on?
Spray cans are quick and even: a whole unit in one session, and a thin, uniform coat. They have the same weather problem as spray primer. Cold, damp or very hot air causes the frosting described below. Shake the can for a full minute, spray in short passes from about 20 to 30 cm, and do two light coats rather than one heavy one. Army Painter's Anti-Shine is a 400 ml aerosol and the Colour Forge can holds 500 ml, by the makers' own figures.
Brush-on varnish in a pot or dropper bottle gives you control and works indoors in any weather. It is slower on a big army, and a heavy coat can pool in recesses and dry cloudy, so thin it a little and brush it out. Citadel's brush-on varnishes are Stormshield (satin) and ’Ardcoat (gloss); Vallejo, Monument Pro Acryl and Army Painter sell brush-on matt varnishes in bottles, and most of these can also go through an airbrush.
Airbrushed varnish is the best of both for anyone with an airbrush: thin, even and indoor. Thin the varnish as you would a paint and spray at a low pressure. See airbrush thinner for what to thin it with.
When and how to varnish
- Let the paint cure. Touch-dry is not cured. Leave the model at least overnight before varnishing, longer after heavy washes or thick contrast coats.
- Varnish before you add static grass and tufts. Spray varnish can flatten or discolour grass; glue tufts on after.
- Two thin coats, letting the first dry fully.
- Gloss details last. Eyes, gems and blood get a brush of gloss once the matt is dry.
- Never varnish metallics with ultra matt unless you want them dulled. Mask them, or paint them after the matt coat.
How to fix frosted varnish
Frosting is a white, cloudy haze over the model after spraying. It happens when the varnish dries too fast or traps moisture: humid air, cold air, a can held too far away, or a coat that was too heavy.
- Prevent it: spray only in dry, mild weather, keep the can at room temperature, and spray closer with lighter passes.
- Fix it with gloss: brush or spray a coat of gloss varnish over the frosted area, which often clears the haze, then re-matt it with a brush-on matt varnish on a dry day.
- Last resort: strip the model and start again. See how to strip paint from miniatures.
A matt brush-on varnish applied too thickly can also dry milky in recesses. Thin it slightly and brush it out.
Few shops we track in this market sell a dedicated matt varnish yet, so some of the products above may not appear. Citadel's brush-on Stormshield (satin) and ’Ardcoat (gloss) are sold here, and a matt coat can follow once a local shop lists one.
Questions people ask
What is the best matt varnish for miniatures? For a whole army in good weather, a spray such as Army Painter Anti-Shine or the Colour Forge matt can. For control in any weather, a brush-on bottle such as Vallejo Polyurethane Matt or Pro Acryl Matte Varnish.
Do I need to varnish miniatures? If they will be played with, yes. Display pieces handled rarely can go without, but a gaming army wears through its edges quickly.
Can I put matt varnish over gloss? Yes, and it is a common routine: gloss for toughness, matt on top to kill the shine.
Why did my varnish go white? That is frosting: humidity, cold, or a heavy coat. Recover it with gloss, then re-matt in better conditions.
Does varnish yellow over time? Many hobby varnish makers describe theirs as non-yellowing, so check the maker's page before buying. Household varnishes are not always made with that in mind.
Matt varnish for miniatures
A matt spray for the army and a brush-on bottle for wet days covers every situation.
We earn a small commission from qualifying purchases at no extra cost to you.
