Hobby SupermarketHobbySupermarket

Curing Resin Prints: Wash and Cure Stations

Wash, dry, then cure: one box or two, and how to size a station to your printer

Every resin print is finished in three steps: wash off the liquid resin, let it dry completely, then cure it under UV light until it is fully hard. A wash and cure station does the first and last in one machine, sized to your printer's build plate. These are the stations sold by the shops we track in the most markets:

ELEGOO Mercury Plus V3.0 Wash & Cure Station

Combined UV curing and IPA/water washing station for resin prints, current flagship model

ELEGOO

  • free AU delivery over A$70, A$7 flat rate below that, 3-7 business days · 14-day returns
Anycubic Wash & Cure 3

Combined ultrasonic wash and UV cure station for resin prints, the entry model in Anycubic's current line

Anycubic

  • postage per seller
  • postage per seller
  • postage per seller
Anycubic Wash & Cure 3 Plus

Larger-capacity wash and UV cure station, fits taller/wider prints than the base Wash & Cure 3

Anycubic

  • postage per seller
  • postage per seller
  • postage per seller
Phrozen Wash & Cure Kit

Combined wash and UV cure station for resin prints

Phrozen

  • postage per seller
  • postage per seller
  • postage per seller

Every station, lamp and chamber we track is on the UV curing shelf.

How to wash and cure resin prints

  1. Wash. Standard and ABS-like resins wash in isopropyl alcohol (IPA); water-washable resin in water. A wash station spins or agitates the liquid around the print.
  2. Dry. Let the print dry completely. Formlabs' instruction for its own station is to "always wash and fully dry parts before post-curing", because solvent left on the part leaves deposits inside the curing chamber. Phrozen gives the same advice for its water-washable tough resin.
  3. Cure. Put the print under UV light, turning it if your station does not, until it is hard and no longer tacky.

How long to cure resin prints

The right time depends on the resin and the light, so start from the time on your resin's bottle or its maker's page. Our best resin for miniatures guide compares the resins. Stations set the time with a timer, so once you know the figure for your resin, each batch gets the same.

All-in-one wash and cure stations

One machine with a wash tank and a turntable under UV lamps. You swap the tank for the turntable between the two steps. The main thing to check is size: the station has to fit your printer's build plate, or the biggest print you make.

StationWash size (max)Cure size (max)Stated details
ELEGOO Mercury Plus V3.0230 x 135 x 260 mm without the plate; 214 x 135 x 180 mm with it250 mm across, 290 mm highUV cover blocks 99.9% of UV; curing stops when the cover is lifted
Anycubic Wash & Cure 3.0165 x 100 x 180 mm without the plate160 x 180 mm3 L tank; Anycubic sizes it for printers of 7.3 inches or less; 405 nm light

Figures from 3DJake's listings for each station. The larger Anycubic Wash & Cure 3 Plus and 3 Max take taller and wider prints; the Max is sized for Anycubic's P1 Max and M7 Max printers.

ELEGOO Mercury Plus V3.0 Wash & Cure Station

Combined UV curing and IPA/water washing station for resin prints, current flagship model

ELEGOO

  • free AU delivery over A$70, A$7 flat rate below that, 3-7 business days · 14-day returns
ELEGOO Mercury Plus V2.0 Wash & Cure Station

Combined UV curing and IPA/water washing station for resin prints

ELEGOO

  • free AU delivery over A$70, A$7 flat rate below that, 3-7 business days · 14-day returns
Anycubic Wash & Cure 3

Combined ultrasonic wash and UV cure station for resin prints, the entry model in Anycubic's current line

Anycubic

  • postage per seller
  • postage per seller
  • postage per seller
Anycubic Wash & Cure 3 Plus

Larger-capacity wash and UV cure station, fits taller/wider prints than the base Wash & Cure 3

Anycubic

  • postage per seller
  • postage per seller
  • postage per seller
Anycubic Wash & Cure 3 Max

Largest wash and UV cure station in the current range, sized for the P1 Max and M7 Max printers

Anycubic

  • postage per seller
  • postage per seller

In this edition the shops we track sell all-in-one stations but not separate washers, ultrasonic cleaners or UV lamps yet, so the next sections show no cards here. The all-in-one stations above do both jobs.

Separate washers and curing chambers

Two machines cost more and take more bench space, but you can wash one batch while the last one cures, and each machine can be bigger than an all-in-one. ELEGOO's Mercury XS bundle is a wash station and a cure station sold together.

Ultrasonic cleaners

An ultrasonic cleaner washes with vibration rather than a spinning tank. The Phrozen and VEVOR cleaners here are listed for washing resin prints in a sealed jar of IPA that stands in the cleaner's water bath, so the alcohol stays in the jar and out of the tank.

UV lamps and curing chambers on a budget

If you already have a wash tub, a UV chamber or lamp does the curing. Green Stuff World's UV Curing Chamber is a mirrored 405 nm chamber of 195 x 160 x 150 mm inside, and its UV torch spot-cures a join or a small part. Gluing resin parts with a dab of resin is covered in our glue guide for 3D prints.

A resin printing workspace: bench, ventilation and the wash and cure station

Resin printing is messy and smelly before it is difficult, so set the workspace up before you pour the first bottle.

  • A room with a window, away from where you sleep and eat. Liquid resin and the alcohol you wash it in both give off a smell, and the resin's own safety data sheet tells you what to wear and how to ventilate.
  • A bench you can wipe down, with the printer, the wash station and the curing station in one line: print, wash, dry, cure. Lay down a disposable mat or tray under all three, since spills happen at the moment you move a plate.
  • Nitrile gloves and eye protection for handling liquid resin and anything still wet. Nitrile gloves are not fully resin-proof, so change them if resin gets on them, wash skin with soap and water, and do not look at the UV lamp or leave skin under it.
  • A steady temperature. Resin flows and cures best at a stable room temperature, which is the main reason people put a printer in an enclosure. Our 3D printer enclosure guide covers tents, rigid boxes and what they do for fumes.
  • A place to leave the wash station and the used IPA, with the lid on, away from heat and any ignition source: IPA is flammable.

An activated-carbon air purifier reduces the smell. ELEGOO, Anycubic and Phrozen each sell one made for their own printers, and a ventilated tent holds the whole printer. An enclosure or purifier is an addition to ventilating the room, not a replacement for it.

In this edition the shops we track list ELEGOO's mini air purifier but not resin tents, so most cards in this section are empty. The wash and cure stations above and the washing buckets below are listed where you shop.

ELEGOO Washing Bucket for Mercury Plus V2.0

Spare part for 3D printer

ELEGOO

  • free AU delivery over A$70, A$7 flat rate below that, 3-7 business days · 14-day returns

Getting rid of the wash liquid

Used IPA and wash water carry uncured resin. Phrozen's rule for water-washable resin is: "Don't pour uncured water directly down the drain." Leave it in sunlight for a few days so the resin cures, filter out the solids and put them in the rubbish.

Questions

How long should I cure resin prints?

Start from the time your resin's maker gives, since it depends on the resin and the light. Wash and dry the print fully first.

Do I need a wash and cure station?

No. A tub of isopropyl alcohol (or water for water-washable resin) and a UV lamp or chamber do the same jobs. A station makes it quicker and tidier.

Should prints be dry before curing?

Yes. Formlabs says to always wash and fully dry parts before post-curing, and Phrozen gives the same advice for its water-washable tough resin.

Where should I set up a resin printer?

In a room with a window, away from where you sleep and eat, on a wipe-clean bench in a line from print to wash to cure. An enclosure or air purifier helps with the smell, and the room still needs ventilating.

Can I pour resin wash water down the drain?

No. Phrozen says not to. Let the water stand in sunlight until the resin in it cures, then filter out the solids.

We compare what the makers and the shops we track publish, and their prices; we have not used these stations ourselves.

Price the hobby

Everything named on this site carries its price across the shops we track.

Hobby Supermarket

Prices on miniatures, paints, brushes, 3D printing and trading cards, compared across the shops we track in the UK, US, Europe, Canada and Australia.

Deals by email

Send me deals for
Tell us what you play (optional)
What are you into? (optional)
Which games?
Which card games?

As an Amazon Associate we earn from qualifying purchases. We also earn commission as a Wayland Games affiliate and through the eBay Partner Network, Awin and other retailer programmes. See how we make money.

Warhammer, Warhammer 40,000, Age of Sigmar, Citadel and Games Workshop are trademarks of Games Workshop Ltd. Magic: The Gathering is a trademark of Wizards of the Coast, Pokémon of Nintendo, Creatures and GAME FREAK, and Yu-Gi-Oh! of Konami. Other product and brand names belong to their owners. Hobby Supermarket is an independent, unofficial site, not affiliated with, endorsed or sponsored by any of them.

Featured on tools.cafe