The Elegoo Mars is the 7-inch resin printer and the Saturn is the 10-inch one. For miniatures the detail is close. The current Mars 5 Ultra has 18 µm pixels and the Saturn 4 Ultra 19 x 24 µm, so a 28 mm face prints much the same on either.
What changes is the plate. A Saturn's plate has a little over twice the area of a Mars plate: a whole unit or a vehicle hull in one run instead of a squad. Buy a Mars if you print a few models a week, a Saturn if you print units, tanks or batches. Anycubic's Photon range splits the same way. The Photon Mono 4 is its Mars-sized printer; the Photon P1 and Photon Mono M7 Pro are its Saturn-sized ones. These are the two sizes from each maker, as sold by the shops we track:

9K, 7-inch monochrome LCD resin printer, the upgraded Mars 5 model
ELEGOO

12K, 10-inch monochrome LCD resin printer, the upgraded Saturn 4 model
ELEGOO

9K mono-LCD MSLA resin printer, the upgraded Mars 4 model
ELEGOO

12K mono-LCD MSLA resin printer, the upgraded Saturn 3 model
ELEGOO
Every resin printer we compare is on the 3D printers shelf, priced in your currency. If you are still choosing between makers and sizes in general, our best resin 3D printer for miniatures guide covers Phrozen and Creality too.
How many miniatures fit on one plate
This is the number that decides between a Mars and a Saturn, so here it is first, as plain arithmetic: how many bases fit flat on each plate in a grid with a 2 mm gap. Treat it as a yardstick for comparing printers, not a promise. Real plates are usually filled with models tilted on supports, and many painters print bases separately, which changes the count both ways.
| Printer family | Plate area | 25 mm bases | 32 mm bases |
|---|---|---|---|
| ELEGOO Mars 5 | 128 cm² | 15 | 8 |
| ELEGOO Mars 4, Mars 4 Ultra, Mars 5 Ultra | 119 cm² | 10 | 8 |
| Anycubic Photon Mono 4, Mono 4 Ultra | 133 cm² | 15 | 8 |
| ELEGOO Saturn 3, 3 Ultra, 4, 4 Ultra | 269 cm² | 32 | 18 |
| ELEGOO Saturn 4 Ultra 16K | 251 cm² | 28 | 18 |
| Anycubic Photon P1, Photon Mono M7 Pro | 281 cm² | 32 | 18 |
| ELEGOO Jupiter 2, Anycubic Photon Mono M7 Max | about 490 cm² | 66 | 32 |
So a Mars plate holds a 10-model infantry squad on 25 mm bases, or eight models on 32 mm bases. A Saturn plate holds a 20-model unit on 25 mm bases with room left over, or 18 models on 32 mm bases. The Saturn's height matters too: 220 to 260 mm against the Mars's 150 to 175 mm, so a tall model or a tank hull standing on end fits on a Saturn where it might not on a Mars.
One surprise from the arithmetic: the entry-level Mars 5, with its wider 89.6 mm plate, fits more 25 mm bases than the Mars 5 Ultra, whose plate is longer but narrower. It pays for that with much larger pixels, 35 µm against 18 µm.
Mars vs Saturn at a glance
| Printer | Screen | XY resolution (pixel size) | Build volume (mm) |
|---|---|---|---|
| ELEGOO Mars 5 | 6.6-inch, 4K | 35 x 35 µm | 143.43 x 89.6 x 150 |
| ELEGOO Mars 4 | 7-inch, 9K | 18 µm | 153.36 x 77.76 x 175 |
| ELEGOO Mars 4 Ultra | 7-inch, 9K | 18 µm | 153.36 x 77.76 x 165 |
| ELEGOO Mars 5 Ultra | 7-inch, 9K | 18 x 18 µm | 153.36 x 77.76 x 165 |
| ELEGOO Saturn 3 | 10-inch, 12K | 19 x 24 µm | 218.88 x 122.88 x 250 |
| ELEGOO Saturn 3 Ultra | 10-inch, 12K | 19 x 24 µm | 218.88 x 122.88 x 260 |
| ELEGOO Saturn 4 | 10-inch, 12K | 19 x 24 µm | 218.88 x 122.88 x 220 |
| ELEGOO Saturn 4 Ultra | 10-inch, 12K | 19 x 24 µm | 218.88 x 122.88 x 220 |
| ELEGOO Saturn 4 Ultra 16K | 10-inch, 16K | 14 x 19 µm | 211.68 x 118.37 x 220 |
Figures from ELEGOO's own product pages and from 3DJake's listings of the same printers, read in November 2026. 3DJake is one of the shops we track and lists the makers' specifications in full. We have not printed on these machines.
Every 7-inch Mars here (the Mars 4, Mars 4 Ultra and Mars 5 Ultra) shares one plate, 153.36 x 77.76 mm, and every Saturn from the Saturn 3 on shares another, 218.88 x 122.88 mm. The 6.6-inch Mars 5 is the odd one out, covered above. Inside each family the models differ in height, release system and extras such as Wi-Fi or a camera, not in how many models fit.
Detail: pixel size, not the "K"
The "9K", "12K" and "16K" on the box count pixels across the whole screen, so a bigger screen needs more of them for the same detail. Compare the XY resolution, the size of one pixel, instead: smaller is finer.
- Mars and Saturn at the same tier print a face about equally well. 18 µm and 19 x 24 µm are close enough that resin, exposure and supports matter more on a 28 mm model.
- The Saturn 4 Ultra 16K is the finest of either family, at 14 x 19 µm.
- The Mars 5 is the exception: its 4K screen has 35 µm pixels, about twice the Mars 5 Ultra's. It is the budget way in, and the one Mars where you give up detail.
When to buy a Mars
A Mars suits you if you print a few models at a time, mostly infantry and characters, and want the smaller, cheaper machine that needs less resin to fill its tank. For a first resin printer, that is usually enough.
The Mars 5 Ultra is the current model, with tilt release, an AI camera and automatic levelling listed among its features, and the shops we track sell it in all five markets. The Mars 4 Ultra and Mars 4 have the same pixel size and plate and are still sold. The Mars 5 is the cheapest way into the family, with the larger pixels noted above.

9K, 7-inch monochrome LCD resin printer, the upgraded Mars 5 model
ELEGOO

9K mono-LCD MSLA resin printer, the upgraded Mars 4 model
ELEGOO

9K mono-LCD MSLA resin printer, the current entry point in the Mars 4 line
ELEGOO
When to buy a Saturn
A Saturn suits you if you print whole units, vehicles, terrain pieces or a weekly batch for an army. It costs more and fills a bigger tank, but one overnight run does what would take a Mars two or three. If you know you will print most weeks, the time saved is the reason to buy one.
Mars 5 Ultra vs Saturn 4 Ultra, the two current Ultras: ELEGOO lists the same tilt release, AI camera and automatic levelling on both, and their pixels are 18 µm against 19 x 24 µm. The Saturn 4 Ultra's plate has about 2.3 times the area and it is 55 mm taller, so the choice is size and price, not detail.
The Saturn 4 has the same screen and plate without the Ultra's extras. The Saturn 4 Ultra 16K has the finest pixels and a heated resin tank. The Saturn 3 Ultra and Saturn 3 are the previous generation, with the tallest builds in the family.

12K, 10-inch monochrome LCD resin printer, the upgraded Saturn 4 model
ELEGOO

12K mono-LCD MSLA resin printer, the upgraded Saturn 3 model
ELEGOO

12K mono-LCD MSLA resin printer, the current standard Saturn model
ELEGOO
The shops we track do not sell the Mars 5, Saturn 4 or Saturn 4 Ultra 16K in this edition, so those cards do not show here. The Mars 5 Ultra, Mars 4 Ultra, Mars 4, Saturn 4 Ultra, Saturn 3 Ultra and Saturn 3 are all on sale from the shops we track.
Elegoo vs Anycubic: the Photon equivalents
Anycubic's Photon printers line up against the same two sizes, and on their makers' figures they have slightly finer pixels and slightly larger plates than the ELEGOO printer of the same size.
| Printer | Screen | XY resolution | Build volume (mm) | Closest ELEGOO |
|---|---|---|---|---|
| Anycubic Photon Mono 4 | 7-inch, 10K | 17 x 17 µm | 153.4 x 87 x 165 | Mars 5 Ultra |
| Anycubic Photon Mono 4 Ultra | 7-inch, 10K | 17 x 17 µm | 153.4 x 87 x 165 | Mars 5 Ultra |
| Anycubic Photon P1 | 10.1-inch, 14K | 16.8 x 24.8 µm | 223 x 126 x 230 | Saturn 4 Ultra |
| Anycubic Photon Mono M7 Pro | 10.1-inch, 14K | 16.8 x 24.8 µm | 223 x 126 x 230 | Saturn 4 Ultra |
| Anycubic Photon Mono M7 Max | 13.6-inch, 7K | 46 x 46 µm | 298 x 164 x 300 | Jupiter 2 |
Figures from Anycubic's own store pages and from 3DJake's listings, read in November 2026.
The bigger difference is where you can buy them. The shops we track sell ELEGOO's Mars and Saturn printers in all five of our markets, and the Photon range mainly in the UK and the US. A printer sold locally is one you can get film and spare parts for locally.
The shops we track do not sell Anycubic's Photon printers in this edition, so the cards above stay empty here. ELEGOO's Mars and Saturn printers are on sale from the shops we track in this edition.
Bigger than a Saturn
For terrain, large vehicles or printing for a club, ELEGOO's Jupiter 2 and Anycubic's Photon Mono M7 Max have plates of about 300 x 162 mm, nearly twice a Saturn's, and 300 mm of height. The M7 Max's pixels are 46 µm, though, so for infantry detail a Saturn-sized printer is the better buy.
Resin and curing for either size
Whichever size you buy, the resin matters as much as the printer for gaming models that get handled: our best resin for miniatures guide compares ABS-like, standard and water-washable resin. Every print also has to be washed and cured, and our curing resin prints guide compares the stations to match your plate.
The whole process, from file to primed model, is in how to 3D print miniatures.
Questions
Is the Elegoo Saturn better than the Mars for miniatures?
Not for detail. The current Mars 5 Ultra has 18 µm pixels and the Saturn 4 Ultra 19 x 24 µm, so a single model prints much the same. The Saturn's plate has a little over twice the area, so it prints more models per run.
How many miniatures fit on an Elegoo Mars plate?
Laid flat in a grid with a 2 mm gap, about 10 models on 25 mm bases or 8 on 32 mm bases fit a Mars 5 Ultra plate. A Saturn 4 Ultra plate fits about 32 and 18. Models tilted on supports change the count.
Is Anycubic or Elegoo better for miniatures?
On the makers' figures the Anycubic Photon Mono 4 and Photon P1 have slightly finer pixels and slightly larger plates than the Mars 5 Ultra and Saturn 4 Ultra. The shops we track sell ELEGOO in all five of our markets and the Photon range mainly in the UK and US.
Does a 16K printer give better miniatures than a 12K one?
Only if its pixels are smaller. The Saturn 4 Ultra 16K's pixels are 14 x 19 µm against the Saturn 4 Ultra's 19 x 24 µm, so it is finer. Compare pixel size, not the K number, because the K counts pixels across screens of different sizes.
We sell no 3D models and host no files: print only files you have the right to print, from their sculptor or publisher.

